ASUS IPIBL-LA MANUAL PDF

년 4월 30일 IPIBL-LA (Berkeley-GL8E) (M) ASUS IPIBL-LA ( BERKELEY-GL8E). Looking for it help would be appreciated. — @[email protected] Might, Courage, Vision, SINCERITY. / v \ Simplicity is Beauty! May the Force and Farce be. The Asus IPIBL-LA is compatible with Intel processors with the LGA / Socket T socket. It has 8 GB DDR2 maximum RAM and conforms to the Micro-ATX form.

Author: Dojin Voodooran
Country: Albania
Language: English (Spanish)
Genre: Travel
Published (Last): 1 March 2006
Pages: 370
PDF File Size: 6.14 Mb
ePub File Size: 4.33 Mb
ISBN: 416-2-26571-892-4
Downloads: 45854
Price: Free* [*Free Regsitration Required]
Uploader: JoJoshicage

Locate the CPU socket on the motherboard. Press the load lever with your thumb Athen move it to the left B until it is released from the retention tab. Retention tab PnP cap Load lever This side of the socket box should face you.

SOLVED: Manual for ipibl-la – Fixya

Close the load plate Athen push the load lever B until it snaps into the retention tab. Under Linux, use the Hyper-Threading compiler to compile the code. If you are ipibl-lz any other operating systems, disable the Hyper-Threading Techonology item in the BIOS to ensure system stability and performance. Use any of the recommended configurations on the next page.

Manual for ipibl-la

manua Failure to do so can cause severe damage to both the motherboard and the components. To install a DIMM: Expansion slots In the future, you may need to install expansion cards. The following sub-sections describe the slots and the expansion cards that they support. Make sure to unplug the power cord before adding or removing expansion cards. Failure to do so may cause you physical injury and damage motherboard components.

Installing an expansion card To install an expansion card: Before installing the expansion card, read the documentation that came with it and make the necessary hardware settings for the card. Remove the system unit cover if your motherboard is already installed in a chassis.

  COUTURAT OPUSCULES PDF

Remove the bracket opposite the slot that you intend to use. Keep the screw for later use. Align the card connector with the slot and press firmly until the card is completely seated on the slot.

Secure the card to the chassis with the screw you removed earlier. Replace the system cover. Configuring an expansion card After installing the expansion card, configure it by adjusting the software settings. The figure shows a graphics card installed on the PCI Express x16 slot. The figure shows a network card installed on the PCI Express x1 slot. Turn OFF the computer and unplug the power cord.

Plug the power cord and turn ON the computer. Removing the cap will cause system boot failure! Side Speaker Out port gray. This port connects to the side speakers in an 8-channel audio configuration.

Rear Speaker Out port black. This port connects to the rear speakers on a 4-channel, 6-channel, or 8-channel audio configuration. Line In port light blue. Audio 2, 4, 6, or 8-channel configuration Headset. Internal connectors This section describes and illustrates the internal connectors on the motherboard. Insert one end of the cable to this connector, then connect the other end to the signal connector at the back of the floppy disk drive. Pin 5 on the connector is removed to prevent incorrect cable connection when using an FDD cable with a covered Pin 5.

Connect the IEEE a module cable to this connector, then install the module to a slot opening at the back of the system chassis. Doing so will damage the motherboard!

  INSTRUCCIONES ROOMBA 760 PDF

Connect the USB module cable to any of these connectors, then install the module to a slot opening at the back of the system chassis. Connect the fan cables to the fan connectors on the motherboard, making sure that the black wire of each cable matches the ground pin of the connector.

Do not forget to connect the fan cables to the fan connectors. Insufficient air flow inside the system may damage the motherboard components.

These are not jumpers! DO not place jumper caps on the fan connectors. Connect the chassis power LED cable to this connector. The axus power LED lights up when you turn on the system power, and blinks when the system is in sleep mode.

Page of 24 Go. Table of Contents Add to my manuals Add.

Motherboard Layout Motherboard layout Page 8 Close the load plate Athen push the load lever B until it snaps into the retention tab.

Expansion Slots Expansion slots In the future, you may need to install expansion cards. Page 17 Audio 2, 4, 6, or 8-channel configuration Headset.

System Panel Connector Comments to this Manuals Your Name. Enter ipibll-la from picture: By pressing ‘print’ button you will print only current page.

To print the manual completely, please, download it. Don’t show me this message again. Got it, continue to print. Don’t have an account?