ASTM A682 PDF

ASTM A Standard Specification for Steel Strip, High Carbon, Cold Rolled, General Requirements. Find the most up-to-date version of ASTM A at Engineering ASTM A, AM – Designation: A /A M – 02 An American National Standard Standard Spe.

Author: Nagami Faezuru
Country: Mexico
Language: English (Spanish)
Genre: Sex
Published (Last): 8 January 2004
Pages: 421
PDF File Size: 11.4 Mb
ePub File Size: 7.85 Mb
ISBN: 684-6-93175-799-2
Downloads: 72537
Price: Free* [*Free Regsitration Required]
Uploader: Brajora

Strip is classified as product that is 0. Normal coiling or piling does not provide a 3 Where an ellipsis. ASTM International takes ashm position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard.

ASTM A682 Grade 1074

Government procurement by the Defense Supply Agency, strip material shall be continuously marked for identi? Link to Active This link will always route to the current Active version of the standard. However, unless the order speci? However, unless the order specifies the applicable “M” specification designation SI unitsthe material shall be furnished to inch-pound units. When the amount of vanadium, columbium, or titanium is less than 0.

Finish and Edges Combining values from the two systems will result in nonconformance with the speci? Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend. Strip is classified as product that is 0.

Notwithstanding the absence of a signature, the organization submitting the EDI transmission is responsible for the context of the report. Last previous edition A — Within the text, the SI units are shown in brackets. Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters. This is produced when the edge condition is not a critical requirement for the?

  BELTRAMI FIELDS IN CHIRAL MEDIA PDF

However, under SI the preferred term in mass. For strip length under 8 ft. If any of the retests fail to comply with the requirements, the coil shall be rejected. This standard has been approved for use by agencies of the Department of Defense.

ASTM A, AM_百度文库

C When edge, width and thickness are not de? The results of analyses taken from different pieces within a heat may differ from each other and from the cast analysis. When the amount of copper, nickel, chromium, or molybdenum is less than 0. Conformance to SI tolerances is mandatory when the “M” specification is used. NOTE 3—When the camber tolerances shown in Table 8 are not suitable for a particular purpose, aatm strip is sometimes machine straightened.

ASTM A Steel, Strip, High Carbon, Cold Rolled, General Requirements

Over 12 Width Tolerance, Plus and Minus, in. A number in parentheses indicates the year of last reapproval. However, unless the order specifies the applicable “M” specification designation SI unitsasttm material shall be furnished to inch-pound units.

The material must be adequately protected and correctly identi? Conformance to SI tolerances is mandatory when the “M” specification is used. If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below.

It astn normally produced as a fully killed steel. Combining values from the two systems will result in nonconformance with the specification.

  COMDEX COMPUTER COURSE KIT PDF

Rework and Retreatment Number of Tests and Retests When atm or more of these elements is speci? Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phonefaxor service astm.

For strip length under mm, camber tolerance shall be subject to negotiation.

This standard is subject to revision at any time by the responsible technical committee and must be reviewed every? Rejection and Rehearing This specification covers the general requirements for cold-rolled carbon spring steel strip in coils or cut lengths. Originally published as A — NOTE 2—Camber tolerances as shown in the table are for any mm length.

When a68, minimum coil weights are subject to negotiation. NOTE 1—The term weight is used when inch-pound units are the standard. Combining values from the two systems will result in nonconformance with the specification. When agreed by purchaser and supplier, other silicon ranges are permissible.

Within the text, the SI units are shown in brackets. The ability of manufacturers to meet the maximum coil weights depends upon individual mill equipment. Limits on such elements are by agreement between purchaser and supplier.